13075398219
山东红晨广告为您济南喷绘,济南喷画,济南喷绘制作,济南喷绘安装,济南喷绘厂家,济南喷画公司,济南写真喷绘作的相关资讯,敬请关注! 收藏本站联系我们

全国服务热线

13075398219

当前位置: 首页 - 新闻中心 > 常见问题 >

新闻中心

UV喷绘在喷画时出现花纹时怎么做?

发布时间:2020-08-27 15:08:51 来源:http://www.jnpenhui.com

1.新式三面翻传动系统构件的原材料
1. Raw materials of the components of the new three side turnover drive system
①关键传动系统构件:拨轮选用铜铝合金铸造成形加工工艺,彻底解决了塑胶构件脆化的难题,确保了三面翻广告牌子的一切正常应用,另外也侧底解决了三面翻拆换构件艰难的难题。
① Key transmission system components: the casting forming process of copper aluminum alloy is adopted for the paddle wheel, which thoroughly solves the problem of brittle plastic components, ensures the normal application of three-sided advertising boards, and solves the difficult problem of three-sided overturning and replacing components.
②新式三面翻尽管选用的也是涤纶拨轮,但其能够轻轻松松取下,使零件拆换时更为轻轻松松便捷。
② Although the new three side turnover is also made of polyester, it can be easily removed, making the parts easier to disassemble and replace.
2.传统式三面翻的铝合金型材三棱柱非常容易弯折:其界面的平面度低,叶子常常撞击非常容易导致三面翻机的毁坏 三面翻的三棱柱在弯折后很容易造成界面互相撞击、造成 设备毁坏它是三面翻的*大难点。
2. The triangular prism of traditional three side turnover aluminum alloy profile is very easy to bend: the flatness of its interface is low, and the leaves often collide with each other, which is very easy to cause the damage of the three side turnover machine. After bending, the triangular prism of three side turnover is easy to cause the interface to collide with each other and cause equipment damage. It is the major difficulty of three side turnover.
新式三面翻广告牌子的每一个零部件在原厂前都是历经严苛的检测。一部分生产厂家开发设计出了三棱柱"电子器件验直机",它是中国三面翻同业竞争中唯*的高精密三棱柱验直机器设备,根据这道检测程序流程,充分保证了三棱柱的竖直,及其安裝后全部三面翻广告牌子的高品质运行。
Every part of the new three sided advertising brand has undergone rigorous inspection before the original factory. A number of manufacturers have developed and designed the prism "electronic device straightening machine", which is the only high-precision trilateral prism straightening machine in China's horizontal competition. According to this testing procedure, the verticality of the prism and the high-quality operation of all the trihedron billboards after installation are fully guaranteed.
3.处理转动轴破裂或歪曲难题
3. Handle the problem of fracture or distortion of rotating shaft
传统式三面翻广告牌子常有转动轴破裂、歪曲状况。由于一般状况下,转动轴都必须驱动器六米上下、几十个拨轮的界面,在遭受摩擦阻力时,因为转动轴的直徑过小因此非常容易歪曲形变。
The traditional three side turnover advertisement board often has the situation of broken and distorted rotating shaft. In general, the rotating shaft must drive the interface of six meters up and down and dozens of dialing wheels. When suffering from friction resistance, because the diameter of the rotating shaft is too small, it is very easy to distort and deform.
济南喷绘安装
新式三面翻广告牌子将转动轴直徑开展了字体加粗、使转动轴扭矩比传统式三面翻机提升了一倍之上。
The new type of three side turnover advertisement brand makes the diameter of the rotating shaft bold, so that the torque of the rotating shaft is more than twice that of the traditional three side turnover machine.
4.新式三面翻的控制回路简易,便于维护保养
4. The control circuit of the new three side turnover is simple and easy to maintain
传统式三面翻电源电路过度繁杂:全部电动机电缆线、摄像头广告牌子电缆线必须根据"总电动机"。一台一般三面翻机少的10几个路线,多则几十条,出現难题没办法开展常见故障清查。要不是技术专业工作人员没办法查验,而电源电路也非常容易因干电源电路出現错乱而使三棱柱旋转时互相撞击或导致界面传动系统顺序紊乱
The power supply circuit of traditional three side turnover is too complicated: all motor cables and camera advertising brand cables must be in accordance with the "total motor". A general three side turnover machine less than 10 routes, more than dozens, there are problems, there is no way to carry out the common fault inventory. If it is not for the technical professional staff can not check, and the power circuit is also very easy to make the triangular prism collide with each other when rotating due to the disorder of the dry power circuit, or cause the interface transmission system sequence disorder

相关推荐

首页 产品 电话 置顶

鲁公网安备 37011202001068号