13075398219
山东红晨广告为您济南喷绘,济南喷画,济南喷绘制作,济南喷绘安装,济南喷绘厂家,济南喷画公司,济南写真喷绘作的相关资讯,敬请关注! 收藏本站联系我们

全国服务热线

13075398219

当前位置: 首页 - 新闻中心 > 公司新闻 >

新闻中心

广告标识中可以使用哪些常识进行安装?

发布时间:2020-10-23 18:10:08 来源:http://www.jnpenhui.com

1、标识制作安装:粘贴式
1. Sign production and installation: paste type
粘贴式应用范围广泛,常用的粘合胶有玻璃胶、泡沫胶、结构胶等。要根据广告标识材质及安装环境、内外干湿、温差等各种情况综合考虑,选择合适的胶粘剂。发光字运用最多的粘贴方式是玻璃胶安装,像树脂字、无边字、注塑字都可选择玻璃胶粘贴式安装。
The adhesive type is widely used. The commonly used adhesives are glass glue, foam glue, structural adhesive, etc. According to the advertising signs material and installation environment, internal and external dry and wet, temperature difference and other comprehensive consideration, choose the appropriate adhesive. The most commonly used pasting method of luminous words is glass glue installation, such as resin words, borderless words and injection molding words, glass adhesive installation can be selected.
2、标识制作安装:粘贴吊挂式
2. Sign production and installation: paste hanging type
适用于一些折边标识。如果安装墙体基础是大理石、玻璃、不锈钢这类不允许打孔,而且又坚固平整的安装墙,那这种方法是最适合不过的了。首先准确测量好安装位置,以防把标识装歪,用AB胶将有机边条或角铝等材料粘在墙体上,然后将标识折边挂上,微调位置,用玻璃胶固定即可。
Suitable for some hem marks. If the foundation of the installation wall is marble, glass, stainless steel, which is not allowed to drill holes, but also solid and flat installation wall, then this method is the most suitable. First, accurately measure the installation position to prevent the sign from being skewed. Use AB glue to stick the organic edge strip or angle aluminum and other materials on the wall, then hang the folded edge of the sign, fine tune the position, and fix it with glass glue.
3、标识制作安装:吊挂固定式
3. Sign production and installation: hanging fixed type
这是针对一些折边标识,体积较大、质量重、用泡沫填充粘贴无法安装所采用的方式。首先确定打孔点,用冲击钻打孔,钉上胶塞及自攻螺丝。只用一只螺丝时,必须在标识标牌的上沿中间部位打孔,以保持水平,然后将标识折边挂在螺丝上,调整位置后,四周封上玻璃胶固定即可。
This is for the use of some flanging labels, large volume, heavy weight, with foam filling and paste can not be installed. First of all, determine the drilling point, punch with an impact drill, screw on the rubber plug and self tapping screw. When only one screw is used, a hole must be drilled along the middle part of the sign plate to keep it horizontal. Then hang the folded edge of the sign on the screw. After adjusting the position, seal the glass glue around for fixing.
4、标识制作安装:底板内部打螺丝式
4. Sign making and installation: screw type inside the bottom plate
济南喷绘安装
这种安装方法针对于金属底盒的标识,如吸塑字、平面发光字这类标识。安装时先根据测量的尺寸在安装墙及标识金属底板上钻好孔,将底盒用螺丝固定于安装墙上,再将字壳用螺丝安装于底盒上面。
This installation method is aimed at the identification of metal bottom box, such as blister character and plane luminous character. During installation, first drill holes on the installation wall and the metal bottom plate of the sign according to the measured size, fix the bottom box on the installation wall with screws, and then install the word shell on the bottom box with screws.
5、标识制作安装:悬挂式
5. Sign making and installation: hanging type
这种方式所采用的吊链材料主要有铁链、钢索、吊鱼丝、扎带等。可根据室内外环境、标识标牌制作重量及其它一些特殊要求采用合适吊装材料。吊牌灯箱通常就是运用这种安装方法。
The main chain materials used in this way are iron chain, steel cable, hanging fish wire, tie belt, etc. Suitable hoisting materials can be used according to the indoor and outdoor environment, the weight of signs and other special requirements. Hanging tag light box is usually used in this way of installation.
6、标识制作安装:落地式
6. Sign production and installation: floor type
根据设计要求,将标识放置于相应位置即可。金属双面字大部分以落地式的方式安装。
According to the design requirements, the logo can be placed in the corresponding position. Most of the metal double-sided characters are installed on the floor.
7、标识制作安装:填埋式
7. Sign production and installation: landfill type
适用于地面为土壤结构,标识不需要移动的情况。根据标识的大小、高低来确定要挖的坑的大小以及所需要用到的混凝土的多少。宣传栏、导视牌大部分都运用这种方式安装。
It is suitable for the case that the ground is of soil structure and the identification does not need to be moved. According to the size and height of the logo, the size of the pit to be excavated and the amount of concrete needed to be used are determined. Most billboards and guide signs are installed in this way.
8、标识制作安装:螺杆安装式
8. Sign production and installation: screw installation
螺杆安装是在标识的底板上焊接有一定长度的螺杆,安装墙面有相应的安装孔,安装时标识的螺杆直接插入对应的安装孔固定即可。螺杆安装是为了使标识离安装墙面之间具有一定的间距。在发光字中,背打光字基本都是运用螺杆安装,这是考虑到它本身的发光特性。
Screw installation is to weld a certain length of screw on the bottom plate of the logo, and there are corresponding installation holes on the installation wall. When installing, the screw with identification can be directly inserted into the corresponding installation hole for fixation. Screw installation is to make the mark have a certain distance from the installation wall. In the light-emitting words, the back light words are basically installed by screw, which is considering its own luminous characteristics.

相关推荐

首页 产品 电话 置顶

鲁公网安备 37011202001068号